進口球型止回閥(德國OLES奧萊斯閥門)

【進口球型止回閥】詳細說明：

多球形止回閥，采用橡膠bao皮滾球為閥瓣，在介質的作用下，可在閥體內的整體式滑道上作上下左右滾動，從而打開或關閉閥門。消聲式關閉，不產生水錘，密封性能好。閥體采用全水流通道，流量大，阻力小，水頭損失比旋啟式小50%。水平或垂直安裝均可，可用于冷水、熱水、工業及生活用水管網系統中，更適應用潛水排水污泵，介質溫度為0～80℃

Multi-spherical check valve, using rubber wrapped ball as valve disc, under the action of medium, can roll up and down on the integral slideway of the valve body, thus opening or closing the valve. The silencing type closes, does not produce water hammer, and has good sealing performance. The valve body adopts full flow passage with large flow rate, small resistance and 50% less head loss than the swing type. It can be installed horizontally or vertically. It can be used in cold water, hot water, industrial and domestic water pipeline system. It is more suitable for submersible sewage pump. The medium temperature is 0-80 C

【進口球型止回閥】結構特點：

1、結構長度短，其結構長度只有傳統法蘭止回閥的1/4~1/8

2、體積小、重量輕、其重量只有傳統微阻緩閉止回閥的1/4~1/20

3、閥瓣關閉快速，水錘壓力小

4、水平或垂直管道均可使用，安裝方便

5、流道通暢、流體阻力小

6、動作靈敏、密封性能好

7、閥瓣行程短、關閥沖擊力小

8、整體結構、簡單緊湊、造型美觀

9、使用壽命長、可靠性高。

1. Structural length is short, and its structural length is only 1/4~1/8 of the traditional flange check valve.

2. Small size, light weight, its weight is only 1/4~1/20 of the traditional micro-blocking check valve.

3. The valve disc closes quickly and the water hammer pressure is low.

4. Horizontal or vertical pipes are available and easy to install.

5. Flow passage is unobstructed and fluid resistance is small.

6. Sensitive movement and good sealing performance

7. Short disc stroke and low impact of valve closure

8. Integral structure, simple and compact, beautiful appearance

9. Long service life and high reliability.

【進口球型止回閥】特性：

滑道滾球式止回閥，采用橡膠bao皮滾動球為閥瓣，在介質的作用下，可在閥體的整體式滑道上作上下滾動，從而打開或關閉閥門，密封性能好，消聲市關閉，不產生水錘。

閥體采用全水流通道，流量大，阻力小，水損失比旋啟式小50%，在水平或垂直安裝均可，可用于冷水、熱水、工業及生活污水管網，更適合潛水排污泵，介質溫度0-80℃。可安裝于水泵出水口處，以防止倒流及水錘對泵損害。

止回閥的啟閉件靠介質流動和力量自行開啟或關閉，以防止介質倒流。止回閥一般分為升降式、旋啟式、蝶式及臥式等四種類型，通式升降式止回閥應安裝于水平管路上，立式升降式止回閥和底閥一般安裝在垂直管路上，并且介質自下而上流動，旋啟式止回閥安裝位置不受限制，通常安裝于水平管路，但也可以安裝于垂直管路或傾料管路上。注意：止回閥只允許介質向一個方向流動，應特別注意介質流動方向，應使介質正常流動方向與閥體上指示的箭頭方向相*，否則就會截斷介質的正常流動。